May 23, 2012, 04:59:24 AM *
Welcome, Guest. Please login or register.
Did you miss your activation email?

Login with username, password and session length
 

Pages: 1st 1 [2]
  Send this topic  |  Print  
Author Topic: Which size bullit rims are good for a 93  (Read 2891 times)
blackstangGT
Jr. Member
**
Posts: 67




Ignore
« Reply #30 on: August 05, 2005, 05:53:19 PM »

damn thats how much those things cost, my friend was tellin gme about a tool that does it? is that the same thing?
Logged

Steve (Member 1,000)
Black 5.0 93 GT
40k miles
Half circles cut into back bumper for 3" tips(Magnaflow)
Pro 5.0 short shifter
BBK Intake(fendermounted)
18" black bullit wheels/reardisc conversion
Dan
Need An Enema?
Badass Supporter
Badass Resident
*
Posts: 20540

Detroit




Ignore
« Reply #31 on: August 05, 2005, 06:36:59 PM »

I am done trying to convince you dude lol. Wink Baseball bat!
Logged

"I don't really like handjobs. I don't like things you give me that I could give myself. Except when I do it, it's a hundred times better. It's like making Emeril Lagasse a microwaved cheeseburger for dinner. Think about the face Emeril would make if you made him Hot Pockets; that's the face I make when I'm getting a handjob."
Dave Heitz
Jr. Member
**
Posts: 117




Ignore
« Reply #32 on: August 06, 2005, 12:26:49 AM »

yea man we rolled my fenders that way and it did look a little ghetto when we were doing it. but it worked good no complaints yet
Logged

Dave
1990 Mustang GT Convertible 25th Anniversary
331  HCI  Every Bolt on....... Money Pit
No better feeling than cruisin with the top down
blackstangGT
Jr. Member
**
Posts: 67




Ignore
« Reply #33 on: August 06, 2005, 12:49:47 PM »

I just got done trying it and went for a drive.....i must say that it rubs a lot less, but still some rubbing, how much did you roll it? untill it was flat against the fender well? another question...someone mentioned to me that in the trunk of the hatch there are two bolts one on each side that adjust the rear suspension, if i were to tighten them would that help? Thanks for your help dan...by the way
« Last Edit: August 06, 2005, 01:43:07 PM by blackstangGT » Logged

Steve (Member 1,000)
Black 5.0 93 GT
40k miles
Half circles cut into back bumper for 3" tips(Magnaflow)
Pro 5.0 short shifter
BBK Intake(fendermounted)
18" black bullit wheels/reardisc conversion
Dan
Need An Enema?
Badass Supporter
Badass Resident
*
Posts: 20540

Detroit




Ignore
« Reply #34 on: August 07, 2005, 07:58:25 AM »

We did roll it until it was pretty much flat against the fender. If you can't roll it any further, take a rubber mallet to it. Again, sounds ghetto, but it will work.

The only two nuts/bolts I can think of are the shock nuts inside the shock tower covers. If you look in the back of your hatch, there are two plastic covers on each side right near the wheels. They cover where you would tighten the shocks at. Tightening them isn't going to do anything to adjust your suspension.
Logged

"I don't really like handjobs. I don't like things you give me that I could give myself. Except when I do it, it's a hundred times better. It's like making Emeril Lagasse a microwaved cheeseburger for dinner. Think about the face Emeril would make if you made him Hot Pockets; that's the face I make when I'm getting a handjob."
Dave Heitz
Jr. Member
**
Posts: 117




Ignore
« Reply #35 on: August 07, 2005, 12:16:38 PM »

yea we had to roll my fenders 3 times before they didnt rub anymore. Have 3 friedns help you. 2 to push the car backwards and one to push down on the hatch. I dont know why but it works better rolling the car backwards. and like pry the bat against the tire and fender.
Hope it works for ya W00t!
Logged

Dave
1990 Mustang GT Convertible 25th Anniversary
331  HCI  Every Bolt on....... Money Pit
No better feeling than cruisin with the top down
blackstangGT
Jr. Member
**
Posts: 67




Ignore
« Reply #36 on: August 08, 2005, 12:24:30 AM »

your right those are the shock bolts...thought they might do something...oh well yea im gonna take a rubber mallet to it sometime this week ill tell you guys how it comes out this is what the car looks like...


* new rims.jpg (170.72 KB, 630x473 - viewed 107 times.)
Logged

Steve (Member 1,000)
Black 5.0 93 GT
40k miles
Half circles cut into back bumper for 3" tips(Magnaflow)
Pro 5.0 short shifter
BBK Intake(fendermounted)
18" black bullit wheels/reardisc conversion
Pages: 1st 1 [2]
  Send this topic  |  Print  
 
Jump to:  

Powered by SMF 1.1.5 | SMF © 2006-2008, Simple Machines LLC